FPGA NIOS II 快速入門教程 適用于初學者 簡單易懂 方便
上傳時間: 2013-08-15
上傳用戶:wfeel
高速FPGA(NIOS II)系統設計和實現
上傳時間: 2013-08-24
上傳用戶:zhyfjj
NIOS II 入門手冊中文版 一、建立quartus ii工程 首先,雙擊quartus ii 9.1圖標打開軟件,界面如下圖1.1所示 1.1 新建工程 (1) 點擊file –>New Project Wizard 出現圖1.2所示的對話框。 (2) 點擊Next。如圖1.3所示:第一行是工程的路徑,二、三行為實體名。填好后點擊Next。 (3)此處可選擇加入已設計好的文件到工程,點擊Next。 (4)選擇設計器件如圖1.5所示。接著點擊Next (5)接著點擊Next。無需改動,點擊finish,顯示如下圖所示。 (6)此時,工程已經建立完成,接下來需要建立一個原理圖輸入文件,點擊file –>New ->Block Diagram/Schematic File 后如圖所示。
上傳時間: 2014-12-25
上傳用戶:cx111111
為了實現對嵌入式系統中大量數據存儲的需求,提出了一種基于NIOS II的SD卡存儲系統設計方案,并完成系統的軟硬件設計。該存儲系統使用SPI模式對SD卡進行讀寫訪問,SPI時序由NIOS II的GPIO模擬產生。將本設計讀取的SD卡的數據與WinHex軟件讀取的SD卡的數據進行比較表明兩者結果一致,達到了設計要求。
上傳時間: 2013-10-11
上傳用戶:ve3344
關于NIOS II 的學習心得。
標簽: NIOS
上傳時間: 2014-01-03
上傳用戶:1421706030
基于Nios-II設計和實現了支持PSTN網絡、Internet網絡的雙網傳真機系統,利用FPGA實現了傳真機系統的多個電路模塊,包括A/D采樣控制邏輯、二值化圖像處理模塊、MH編碼模塊、MH譯碼模塊和CIS掃描、TPH打印、電機控制模塊。基于μC/OS-II、Niche TCP/IP實現了T30協議通信、非實時網絡傳真通信、Tiff文件創建、Tiff文件解析模塊。使用Altera Cyclone EP1C20開發板實現和驗證了整機系統,經過軟硬件聯調,達到了系統設計指標和功能。
上傳時間: 2013-11-13
上傳用戶:xwd2010
基于VHDL的FPGA和NIOS II 實例精煉【作者:劉福奇;出版社:北京航空航天大學出版社】(本書優酷視頻地址:http://www.youku.com/playlist_show/id_5882081.html) 內容簡介:本書分為4個部分:Quartus Ⅱ軟件的基本操作、VHDL語法介紹、FPGA設計實例和Nios Ⅱ設計實例;總結了編者幾年來的FPGA設計經驗,力求給初學者或是想接觸這方面知識的讀者提供一種快速入門的方法;適合電子相關專業的大學生、FPGA的初學者以及對FPGA有興趣的電子工程師。初學者可以按照步驟學習。本書中提及到時間計算問題,不光提出有時間戳的方法, 還介紹了一種通過讀取定時器的寄存器來計算時間的方法。其實,有人認為,本書最好的部分是:DMA的實現說明(本書從3個方面講述了DMA的使用)。現在學習Verilog HDL的人或許比較多,但是用VHDL的人可以學習下,這本書還是很不錯的。
上傳時間: 2014-07-10
上傳用戶:米米陽123
NIOS II軟件構建工具入門 The Nios® II Software Build Tools (SBT) allows you to construct a wide variety of complex embedded software systems using a command-line interface. From this interface, you can execute Software Built Tools command utilities, and use scripts other tools) to combine the command utilities in many useful ways. This chapter introduces you to project creation with the SBT at the command line This chapter includes the following sections: ■ “Advantages of Command-Line Software Development” ■ “Outline of the NIOS II SBT Command-Line Interface” ■ “Getting Started in the SBT Command Line” ■ “Software Build Tools Scripting Basics” on page 3–8
上傳時間: 2013-11-15
上傳用戶:nanxia
使用NIOS II軟件構建工具 This chapter describes the Nios® II Software Build Tools (SBT), a set of utilities and scripts that creates and builds embedded C/C++ application projects, user library projects, and board support packages (BSPs). The NIOS II SBT supports a repeatable, scriptable, and archivable process for creating your software product. You can invoke the NIOS II SBT through either of the following user interfaces: ■ The Eclipse™ GUI ■ The NIOS II Command Shell The purpose of this chapter is to make you familiar with the internal functionality of the NIOS II SBT, independent of the user interface employed.
上傳時間: 2013-10-12
上傳用戶:china97wan
通過以太網遠程配置NIOS II 處理器 應用筆記 Firmware in embedded hardware systems is frequently updated over the Ethernet. For embedded systems that comprise a discrete microprocessor and the devices it controls, the firmware is the software image run by the microprocessor. When the embedded system includes an FPGA, firmware updates include updates of the hardware image on the FPGA. If the FPGA includes a Nios® II soft processor, you can upgrade both the NIOS II processor—as part of the FPGA image—and the software that the NIOS II processor runs, in a single remote configuration session.
上傳時間: 2013-11-22
上傳用戶:chaisz